Infinity Speaker Infinity TOTAL SPEAKER SOLUTIONS User Manual

TOTAL SPEAKER SOLUTIONS  
TSS-SAT800  
Owner’s Guide  
 
INTRODUCTION  
PLACEMENT  
NOTE: The TSS-SAT800 can be placed directly on a shelf,  
Infinity Total Solutions  
or mounted on a wall using the included wall bracket.  
Infinity Total Solutions continues Infinity’s longstanding commitment  
to accurate sound reproduction. Our high-quality drivers, precision  
dividing networks and rigid, well-braced enclosures combine to deliver  
uncompromised performance in any multichannel home theater system.  
In addition, the TSS-SAT800 is magnetically shielded for safe place-  
ment adjacent to a television.  
As Left and Right Front Channels  
For left and right front channels, place one satellite to the left  
and another to the right of the television, as shown in Figure 1.  
Since the speakers are magnetically shielded, you can place  
them very close to the TV without worrying about the magnetic  
field distorting the picture.  
INCLUDED  
As Surround Channels  
For left and right surround channels, place one speaker on the  
left and another on the right, to the side of or slightly behind the  
listening area.The surround speakers should be mounted at a  
height of between 5 ft. (1.5m) and 7 ft. (2m).  
®
In 6- or 7-channel configurations, place the rear channel(s)  
behind the listening position, as shown in Figures 1 and 2.  
(1) Speaker (1) Adjustable (1) Fixed wall (1) Shelf stand with  
wall bracket  
bracket  
two attachment screws  
NOTE: An Infinity powered subwoofer will add impact and realism  
to both music and film soundtracks. Contact your Infinity dealer  
for recommendations on subwoofer models for your application.  
PLANNING YOUR SYSTEM  
Before deciding where to best place your speakers, survey your room and  
study Figures 1 and 2.  
Mounting on Floor Stands  
An optional floor stand is available, should you prefer to place  
your TSS-SAT800 satellites on the floor; see your dealer or visit  
Subwoofer  
keyhole on the back of the speaker to the screwhead on the  
Left Front  
Channel  
Center  
Channel  
Right Front  
Channel  
Couch  
Left Rear  
Channel  
Center Rear  
Channel  
Right Rear  
Channel  
Left  
Surround  
Channel  
Right  
Surround  
Channel  
Figure 1.This overhead view shows a typical home theater plan.  
Left/right rear channels are for a 7-channel system. Center rear  
channel is for a 6-channel system.  
Subwoofer  
Right Front  
Channel  
Center  
Channel  
Right  
Surround  
Channel  
Left Front  
Channel  
Right Rear  
Channel  
Center Rear  
Channel  
Left  
Surround  
Channel  
Left Rear  
Channel  
Figure 2.This figure shows an alternate layout, which may be  
more suitable for some rooms. Left/right rear channels are  
for a 7-channel system. Center rear channel is for a 6-channel system.  
3
TSS-SAT800  
 
Adjustable Wall Bracket  
Step 1. Mark the positions on the wall where you would like to  
place the mounting screws.  
Using the Satellite on the Shelf Stand  
To attach the satellite to the shelf stand, hold the satellite on top  
of the stand and insert the two included screws through the rear  
of the stand and into the rear of the speaker.  
Step 2. Place the bracket against the wall and fasten four 1-1/2"  
#10 wood screws through the bracket’s screw holes into the  
wall. If a wall stud is not available, use an appropriate anchor.  
®
WALL-MOUNTING THE SATELLITES  
The TSS-SAT800 satellite is designed to be mounted on the  
wall.There is a fixed-mount wall bracket and an adjustable wall  
bracket provided for each satellite. Each speaker bracket will  
require up to four 1-1/2"#10 wood screws; each screw should  
be fastened to a wall stud. If a wall stud is unavailable, install an  
anchor appropriate for a 1-1/2"#10 screw.  
Step 3. Unscrew round collar (C) from bracket (A).  
A
C
B
NOTE: The customer is responsible for the correct selection  
and use of mounting hardware (available through hardware  
stores) that will ensure the proper and safe wall-mounting of  
the speakers.  
Fixed-Mount Wall Bracket  
Step 1. Mark the positions on the wall where you would like to  
place the mounting screws.  
Step 2. Attach the back plate of the bracket to the wall using  
three screws (not included).  
Step 3. Attach the front plate (with the spring tab) of the bracket  
to the satellite using the two provided screws.  
Step 4. Slide the speaker with the  
attached bracket front plate  
onto the back plate of the  
bracket until the tab locks into  
place.  
To remove the speaker  
from the wall, simply push in  
the locking tab and slide  
the speaker up.  
keyhole on the back of the speaker to the  
screwhead on the wall. Once positioned  
properly, the speaker should slide down slightly  
and become secure.  
4
TSS-SAT800  
 
Step 4. Screw the ball and shaft assembly (B) to the lower 1/4"-  
20 insert on the rear of the satellite. Back out 1/2 of a turn and  
tighten the nut against the speaker.  
Step 5. Attach the speaker wire as shown on page 6.  
Step 6. Drop round collar (C) over ball and shaft assembly (B)  
that is mounted to the speaker with the finished side of the  
collar facing the rear of the speaker.  
Step 7. Carefully push the ball straight into the socket mounted  
on the wall, angle the speaker as desired and tighten the collar  
using the enclosed metal bar.  
Metal bar  
®
Figure 3. Bracket on wall.  
5
TSS-SAT800  
 
CONNECTIONS  
MAINTENANCE AND SERVICE  
After placing the speakers, you are ready to connect your system.  
First, turn off all audio-system power. Use high-quality speaker  
wire to make your connections; #18-gauge speaker wire with  
polarity coding is recommended. For longer distances, #16-  
gauge or heavier wire is recommended.The side of the wire with  
a ridge or other coding is usually considered positive polarity  
(i.e., +). Also, consult the owner’s manuals that were included  
with your amplifier or receiver to confirm connection procedures.  
Observe polarities when making speaker connections, as shown in  
Figure 4. Connect each + terminal on the back of the amplifier or  
receiver to the respective + (red) terminal on each speaker.  
Connect the – (black) terminals in the same way.  
The TSS-SAT800 enclosure may be cleaned using a soft cloth to  
remove fingerprints or to wipe off dust.  
All wiring connections should be inspected and cleaned or  
remade periodically.The frequency of maintenance depends on  
the metals involved in the connections, atmospheric conditions  
and other factors, but once per year is the minimum.  
If a problem occurs, make sure that all connections are properly  
made and clean. If a problem exists in one loudspeaker, reverse  
the connection wires to the left and right system. If the problem  
remains in the same speaker, then the fault is with the loud-  
speaker. If the problem appears in the opposite speaker, the  
cause is in another component or cable. In the event that your  
TSS-SAT800 ever needs service, contact your local Infinity  
service center near you.  
Important!  
Do not reverse polarities (i.e., + to –, or – to +) when making  
connections. Doing so will cause poor imaging and diminished  
bass response. Be certain that positive and negative wire strands  
are completely isolated to avoid short circuits that may damage  
your equipment.  
Figure 4. Wiring diagram shows polarity connections  
for one channel of a home theater system.  
6
TSS-SAT800  
 
SPECIFICATIONS  
TSS-SAT800  
Frequency Range:  
120Hz – 30,000Hz ( 3dB)  
Recommended  
Amplifier Power Range:  
10 – 100 Watts  
88dB  
Sensitivity:  
(2.83V @ 1 meter)  
Nominal Impedance:  
Crossover Frequency:  
Midrange Driver(s):  
8  
3.5kHz; 12dB/octave  
3-1/2" (64mm) MMD® magnetically shielded  
3/4" (19mm) MMD magnetically shielded  
High-Frequency Driver:  
Dimensions (H x W x D):  
9-1/8" x 3-3/4" x 2-3/4"  
(232mm x 95mm x 70mm)  
Weight:  
2.5 lb (1.1kg)  
Infinity continually strives to update and improve existing products, as well as  
create new ones.The specifications and construction details in this and related  
Infinity publications are therefore subject to change without notice.  
Declaration of Conformity  
We, Harman Consumer Group International  
2, route de Tours  
72800 Château du Loir  
France  
declare in own responsibility that the product described  
in this owner’s manual is in compliance with technical  
standards:  
EN 61000-6-3:2001  
EN 61000-6-1:2001  
Harman Consumer Group International  
Château du Loir, France 2/06  
7
TSS-SAT800  
 
© 2006 Harman International Industries, Incorporated.All rights reserved.  
Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA www.infinitysystems.com  
Infinity and Harman International are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries.  
Total Solutions is a trademark of Harman International Industries, Incorporated.  
Dolby and Pro Logic are registered trademarks of Dolby Laboratories.  
DTS is a registered trademark of DTS, Inc.  
Part No. 406-000-05354-E 2/06  
 

Intel Crib Toy D2700 User Manual
Intermec Network Card 10I2 User Manual
IRIS Indoor Furnishings E4PINSR User Manual
Jensen Car Stereo System MP6610 User Manual
Jensen Flat Panel Television JE2608 User Manual
JVC Computer Drive MC D207U User Manual
Kelvinator Freezer KCS200G W User Manual
Kenmore Range 66575832 User Manual
Kenwood Iron IC400 Series User Manual
Konica Minolta Digital Camera Dimage X20 User Manual